Sponsored

Ohlins Coilover Setup

OptionZero

Well-Known Member
Joined
Oct 25, 2023
Threads
3
Messages
382
Reaction score
303
Location
Norcal
Car(s)
2015 370Z Nismo
Mine are at 14k. My son went over all the numbers and says the same, borderline but the same. Also depends on valving, the rears are very tight. 10 clicks from firm to keep some form of dampening. Will add another 3 or 4 once the fronts and spring length are figured out.

my main problem is spring length and adjustability in the rear. Cannot go lower and keep the springs captivated.

I left SakeBomb another msg noting the spring rate when explaining my spring length problems.
It kinds sounds like Sakebomb should get one of these cars in-hand and sort out some finer details
 

RSS

Well-Known Member
First Name
Scott
Joined
May 23, 2025
Threads
0
Messages
50
Reaction score
16
Location
Indy
Car(s)
ā€˜24 Z
I was under the impression an employee had one now. My biggest gripe is never being able to get a hold of somebody or get semi quick answers To questions. I admit my first set up was done wrong but actually was spot on to what I have now, so same problems.
I spent some time on the phone with my son (he was in the race industry and now teaches this stuff) going over everything after the fact and he’s a little confused by things. Hopefully next week he can stop by and just recheck everything for me Just to verify what he is seeing.
 

Suzuyabot

Well-Known Member
First Name
Dante
Joined
Oct 9, 2024
Threads
2
Messages
75
Reaction score
46
Location
PNW
Car(s)
2024 Nissan Z Nismo
@Suzuyabot did your clunk in the rear go away? I am wondering if you have the same spring lengths as me and when the shop lowered yours the spring is coming off the perch when in droop.
Unfortunately the clunk is still there. I’m not sure about the spring length and the kit was already preloaded when it arrived. But I’m taking the car to shop for toe arms and endlinks with an alignment check first next week so I can check for stuffs. For the spring rates, they are saying they have different specs for springs and valving for nismo. But I don’t know any more details.
 

RSS

Well-Known Member
First Name
Scott
Joined
May 23, 2025
Threads
0
Messages
50
Reaction score
16
Location
Indy
Car(s)
ā€˜24 Z
Yes they do, but spring length should be the same. Not knowing what your spring length is You might want to Jack up the rear of the vehicle to lift wheels off the ground and see if you can freely move the spring side to side some. It might be coming off the perch or your retainer ring between the helper spring and main spring. That would definitely make a clunking noise. Just a thought.
 

Suzuyabot

Well-Known Member
First Name
Dante
Joined
Oct 9, 2024
Threads
2
Messages
75
Reaction score
46
Location
PNW
Car(s)
2024 Nissan Z Nismo
Yes they do, but spring length should be the same. Not knowing what your spring length is You might want to Jack up the rear of the vehicle to lift wheels off the ground and see if you can freely move the spring side to side some. It might be coming off the perch or your retainer ring between the helper spring and main spring. That would definitely make a clunking noise. Just a thought.
Well the noise just disappeared itself and now just some minor squeaking sound, which is something I can accept when upgrading some metal to metal parts. I will still give it a check when doing oil change later this year. As for the spring rates, I got confirmed by SBG team. They said the spring rates are the recommended numbers for the option I chose.
 

Durango 95

Well-Known Member
Joined
Jul 29, 2026
Threads
0
Messages
85
Reaction score
59
Location
West Coast Florida
Car(s)
2026 Nissan Z Performance
Took the dive and added the Ohlins today. Bought from Z1. Went from stock to lowering springs to Ohlins. Blown away by the ride quality. I've done quite a few mods to the car but none have had a greater impact. Street use only. I was worried they would be on the harsh side since they are popular for track and maybe the road quality was more marketing hype or only an afterthought. Took the car in this morning and picked it up by 4:00. Totally exceeded my expectations. So glad I made the move. I was a little hesitant to switch from the lowering springs because I liked the look and handling so I was leery that the differences would only be minor. Big difference. Really nice ride. The only mistake that I made is not having it done sooner.
 

RSS

Well-Known Member
First Name
Scott
Joined
May 23, 2025
Threads
0
Messages
50
Reaction score
16
Location
Indy
Car(s)
ā€˜24 Z
Took the dive and added the Ohlins today. Bought from Z1. Went from stock to lowering springs to Ohlins. Blown away by the ride quality. I've done quite a few mods to the car but none have had a greater impact. Street use only. I was worried they would be on the harsh side since they are popular for track and maybe the road quality was more marketing hype or only an afterthought. Took the car in this morning and picked it up by 4:00. Totally exceeded my expectations. So glad I made the move. I was a little hesitant to switch from the lowering springs because I liked the look and handling so I was leery that the differences would only be minor. Big difference. Really nice ride. The only mistake that I made is not having it done sooner.
Did you stick with the divorced or go true?
 

RSS

Well-Known Member
First Name
Scott
Joined
May 23, 2025
Threads
0
Messages
50
Reaction score
16
Location
Indy
Car(s)
ā€˜24 Z
I went ahead and lowered mine a bit more, SBG said it’s was ok to let the springs drop off perch at full drop as it’s not going to happen often. Currently working on balance, not sure where I stand at the moment.

True coilover with 14k rear
 

Durango 95

Well-Known Member
Joined
Jul 29, 2026
Threads
0
Messages
85
Reaction score
59
Location
West Coast Florida
Car(s)
2026 Nissan Z Performance
Did you stick with the divorced or go true?
I went with the divorced. Set according to Ohlins suggested set up specs. Plan on moving it one more setting towards track. Also, plan on raising the car. It is just too low for the roads I drive. Pretty much any road it's too low. Already had some tire rub. Just getting it dialed in.

IMG_1570.webp
 
Last edited:
OP
OP
FSUZ33

FSUZ33

Well-Known Member
First Name
Chad
Joined
Feb 23, 2025
Threads
46
Messages
1,597
Reaction score
2,020
Location
Tallahassee, FL
Car(s)
ā€˜24 Z NISMO
Not sure if this info is somewhere else here in one spot. If so let me know and I'll delete this.

It would be nice to have sort of a database of this stuff in order to pinpoint when and where things start to rub.
Many want to max out wheel and tire width without having to worry about scrubbing or having to touch any bodywork. Sometimes that can be a very thin line, where one setup works and what seems like the same or very similar setup rubs on another car. Maybe it's because one is running a slightly different front tire size. Maybe front camber is different by a degree. Maybe it's model to model, like the speculation that the NISMO fender "flares" actually increase the gap you need between tire and fender lip.

- Drop
- Wheel size and offset
- Tire size
- Spacers (if applicable)
- Suspension arm/link setup/changes
- Alignment spec's
- And if you are free and clear, rubbing slightly front and/or rear, or had to modify something to keep from rubbing.
 
  • Like
Reactions: RSS

jacksonmagnet

Well-Known Member
Joined
Aug 28, 2026
Threads
4
Messages
103
Reaction score
65
Location
ny
Car(s)
z
Leave stock height, normies think the whole car is stock if it’s not lowered
 

RSS

Well-Known Member
First Name
Scott
Joined
May 23, 2025
Threads
0
Messages
50
Reaction score
16
Location
Indy
Car(s)
ā€˜24 Z
Leave stock height, normies think the whole car is stock if it’s not lowered
Pretty close to stock height as it sits. The rear will get raised a bit closer so my jack clears exhaust for rear jacking point with the awe exhaust. But we are talking maybe a 10mm drop in height total.
 

RSS

Well-Known Member
First Name
Scott
Joined
May 23, 2025
Threads
0
Messages
50
Reaction score
16
Location
Indy
Car(s)
ā€˜24 Z
Getting ride smoothed out, I have a stock alignment at the moment but will have it readjusted. Mine is going To be a work in progress, working with settings, height adjustments plus full SPL in rear and SPL FUCAS. The ride is crisp and I have no rub at all at the moment under normal driving or up/down driveway curb. Front wheel air deflectors will scrape a tad on driveway. Will add wheel specs when I have a minute but APEX wheels with 295/305 Conti’s.

Just went with push clips for the adjustment holes in the rear for now. Once set up I won’t need them accessible as much.

IMG_0048.webp
 
Last edited:

OptionZero

Well-Known Member
Joined
Oct 25, 2023
Threads
3
Messages
382
Reaction score
303
Location
Norcal
Car(s)
2015 370Z Nismo
Getting ride smoothed out, I have a stock alignment at the moment but will have it readjusted. Mine is going To be a work in progress, working with settings, height adjustments plus full SPL in rear and SPL FUCAS. The ride is crisp and I have no rub at all at the moment under normal driving or up/down driveway curb. Front wheel air deflectors will scrape a tad on driveway. Will add wheel specs when I have a minute but APEX wheels with 295/305 Conti’s.

Just went with push clips for the adjustment holes in the rear for now. Once set up I won’t need them accessible as much.

IMG_0048.webp
People don't believe me when I say good coilovers that are properly damped are perfectly liveable, almost the same as stock or better depending on the year and trim (early Z34 Nismo was notoriously garbage)
 
 






Top