What did you do with your Z today? 🙋🏻‍♂️

[traska_rz34]

Aka stock springs with EIBACH written on them in silver Sharpie!

He says after he sells them to me

 

[KrackaC8]

He says after he sells them to me

I Dremel'd an inch of coil off each so they should be around right

 

[KrackaC8]

Just F'ing around, obviously...

The roads are so bad here in Houston around my office is why I changed my mind on lowering. Plus all the ridiculous speed bumps everywhere...

I may add more Z1 chassis bracing though! Currently looking at these two to pair with my current front & rear subframe bars:
https://www.z1motorsports.com/chass...023-nissan-aluminum-brace-p-56231.html?m=NEWZ
https://www.z1motorsports.com/all-s...arance-rear-chassis-brace-p-58425.html?m=NEWZ

 

[thesilverbullet]

Installed the RSR springs yesterday (well my buddy did) the springs are fantastic, car rides stock like just a little sharper. Stance is perfect!

Looking good - paint color choice looking sharp too..

 

[HuskeRZ34]

Just F'ing around, obviously...

The roads are so bad here in Houston around my office is why I changed my mind on lowering. Plus all the ridiculous speed bumps everywhere...

I may add more Z1 chassis bracing though! Currently looking at these two to pair with my current front & rear subframe bars:
https://www.z1motorsports.com/chass...023-nissan-aluminum-brace-p-56231.html?m=NEWZ
https://www.z1motorsports.com/all-s...arance-rear-chassis-brace-p-58425.html?m=NEWZ

I think those are more designed to replace OE steel parts to save weight. I bet it might make the chassis slightly stiffer but nominal. But give it a shot and report back!

 

[kevinbonds]

Very busy morning today! Woke up at 5:15a to wash the car and meet up with some other Z friends to go to Orlando Cars and Coffee. Had a great time, especially being able to chat up other Z owners for the first time.

NIce, next time you are headed to a Florida event send me a DM.

 

[Ikazuchi6]

Today I had my wheel repaired. I curbed it about 2 weeks ago and it's been eating at me. I found a place here in Houston that did an amazing job.

The color match is amazing. Took this pic while in their shop. Alloy Wheel Repair Specialist of Houston. I recommend.js

I would have been sick!

Glad they fixed you up perfect!

 

[Ikazuchi6]

After saving the world one turtle at a time and then mailing off a package, I came home and these were waiting on me. Who was it that showed theirs off earlier in the thread? @KrackaC8? These are how the car should have came from the factory! So much better. Hard to really see the difference in pics.

 

[KrackaC8]

After saving the world one turtle at a time and then mailing off a package, I came home and these were waiting on me. Who was it that showed theirs off earlier in the thread? @KrackaC8? These are how the car should have came from the factory! So much better. Hard to really see the difference in pics.

YES!!! 100%! I love mine.

Kudos to you sir on those turtles!

 

[Mugzilla]

Installed the Burger Motorsports 3d printed longer clutch stop. The clutch now stops higher. However, when you start the Z, you need to push the clutch harder to smoosh the "Push clutch in to start the car".

2 nickels hot glued in front of the old stop would accomplish the same thing.

 

[KrackaC8]

Installed the Burger Motorsports 3d printed longer clutch stop. The clutch now stops higher. However, when you start the Z, you need to push the clutch harder to smoosh the "Push clutch in to start the car".

2 nickels hot glued in front of the old stop would accomplish the same thing.

Oh good, more crap I didn't know I needed!

 

[Ikazuchi6]

Oh good, more crap I didn't know I needed!

This is my initial reaction to half your posts!

 

[FSUZ33]

2 nickels hot glued...

I get the feeling you have spare change glued/attached/rigged to lots of things. Don't get me wrong, if it works it works. Your heirs will have no idea of your total worth until they realize on average there's $0.38 glued into every single thing you own.
$0.20 used to help pop the hatch
$0.10 used to reposition the clutch pedal
$0.27 to shim the tablesaw into alignment
$0.77 to level the toilet
...

 

[Mugzilla]

I get the feeling you have spare change glued/attached/rigged to lots of things. Don't get me wrong, if it works it works. Your heirs will have no idea of your total worth until they realize on average there's $0.38 glued into every single thing you own.
$0.20 used to help pop the hatch
$0.10 used to reposition the clutch pedal
$0.27 to shim the tablesaw into alignment
$0.77 to level the toilet
...

At first I was like -----------------------------Then I was like (Oh yeah. I DID say both of those things.....)



(Except I'm a guy)

 

[Nis Mo Z]

Thanks to the individual who figured out we didn’t have to have the ugly cloudy map lens I had to get mine changed ASAP and my CF radiator plate came in to match the CF intake filters, Z1 engine cover, and Cusco carbon aluminum strut bar.