What did you do with your Z today? 🙋🏻‍♂️

[Resnort]

Stock for stock

It really is strange how much of a size difference there is just because of a gearbox.

 

[JonnyG]

Bought these from Issac Palmer in the Nissan Z FB group - haven't put on yet, this week, weather has been shit. Probably ordering new wheels this week also so might have to order new set but thats OK and I have Z caps from factory.

 

[speedjuno]

Washed, detail wax, garaged, ahead of a rainy week.

 

[staying_tuned]

Starting to paint correct prior to PPF & ceramic. Clayed and decontaminated yesterday. Boulder gray pearl has a lot of charisma, lots of jade flecks in the paint. Hard to tell in this close-up but the complexity & depth really shows through after knocking down Nissan orange peel ; )

 

[Ikazuchi6]

Starting to paint correct prior to PPF & ceramic. Clayed and decontaminated yesterday. Boulder gray pearl has a lot of charisma, lots of jade flecks in the paint. Hard to tell in this close-up but the complexity & depth really shows through after knocking down Nissan orange peel ; )

I never knew. I guess i just assumed Boulder Gray was just a solid color...looks good!

 

[staying_tuned]

Laid down 2 layers of CQuartz UK 3.0 in the rear (PPF going on front early next week). Disregard the shop mess, we are in winter mode. I haven't pulled the wheels yet this round, post PPF I'll pull and hit them with d-lux.

 

[Ikazuchi6]

Added the hood stripe. If i decide I don't like it, it's easily reversible but so far I dig it. I just felt like there was too much yellow on the front that wasn't broken up any kind of way. $47 shipped from SupDec.

It looks straight to me, no bubbles. One tiny speck of something underneath that I can't see but I can feel it when I run my hand over it.

I looked at it 1000 times while laying it down, you can work yourself cross-eyed lol

 

[Ikazuchi6]

Also they recommend the dry install method. I can't imagine. I did the wet and its still a bit tricky but I'm also very novice at this.

 

[5amp5on]

Installed the Z1 carbon fiber engine cover and radiator air guide. As usual everything was packaged carefully and shipped immediately. Even my wife likes it which is saying a lot because she prefers stock on vehicles.

 

[Z_x3]

Stealth PPF for the stealth gray nismo!

 

[staying_tuned]

That looks so sharp, hey is that XPEL’s stealth or another line? Very nice!

 

[D2M]

Stealth PPF for the stealth gray nismo!

This car looks like it still has the shipping spring spacers left in the front.

 

[Z_x3]

This car looks like it still has the shipping spring spacers left in the front.

It had…thanks to one pot hole and the eye
of a few others who brought that to my attention…was able to get her jacked up and the remaining removed. Thanks ? to all again.

 

[ZillaZ]

Yesterday I added the splash guards. I really like them a lot although I know the rears are hit or miss for some ppl.

Today I filled up for the first time and I can tell the engine is responding differently, lots better. I'm sure the ding-dongs at the dealer filled up with cheap gas. Glad to have gotten that tank burned out and gone!

I just ordered some. Pretty easy install from the sounds of it.

I really like the look - especially the rear.

 

[Ikazuchi6]

I just ordered some. Pretty easy install from the sounds of it.

I really like the look - especially the rear.

Thanks man!

Install wasn't hard, the QR code on the paperwork took me to a website that didn't work. So I held them up to the car to figure out where they needed to be. In my case, I ended up throwing out the templates. I taped them to the car and then held the splash guard over the templates to see if the holes lined up. They were off, so I just used the guards themselves to mark my holes.

Not really a big deal and I'm not giving advice, just a heads up that the templates may not line up.

The most unnerving part for me was drilling the hole at the back underneath the bumper. The push pin is larger for that one, you'll see in the kit.