Hands Up all the Aussies

[Supremekai]

I am using the ROOM LAMP for constant power and POWER SOCKET for ACC power. The +/- sides are shown in the pictures.
There are 2 spare slots. The one above TCU is constant, but I can’t plug in a fuse tap as the Transport Mode switch gets in the way?. The one below POWER SOCKET has no power even the car is turned on.?

How did you hide the wires? I'm stuck at the A pillar ?

and where did you put the ground wire?

 

[peter]

I'm guessing that was on sale, but would still love a link?

As black Friday is comming up in the US good time to buy, that's when I most of my stuff, most of the US nissan dealers will have an online parts dep, join their VIP programme for bigger discounts.
The biggest problem is shipping, I set up a US address a while ago and used this, all up was a lot cheaper than buying in OZ, but our dollar has since dived.

 

[MattJ2020]

$160-$300 for a bracket... made of plastic. A joke right?

https://flowbrackets.com.au/?fbclid=IwAR3jDa4kt6NSlAwq8tcfTr7_p6yQCxNC-ZvYLIqkC3nC5jSI0wMxEJghT7A

 

[loudsx]

$160-$300 for a bracket... made of plastic. A joke right?

https://flowbrackets.com.au/?fbclid=IwAR3jDa4kt6NSlAwq8tcfTr7_p6yQCxNC-ZvYLIqkC3nC5jSI0wMxEJghT7A

well that depends on if you bought it or not to know if you are the joke

 

[peter]

$160-$300 for a bracket... made of plastic. A joke right?

https://flowbrackets.com.au/?fbclid=IwAR3jDa4kt6NSlAwq8tcfTr7_p6yQCxNC-ZvYLIqkC3nC5jSI0wMxEJghT7A

easier to cut down and re-fit the original bracket, once done you can't tell, thats if you want to leave it in the same place

 

[GUZ]

$160-$300 for a bracket... made of plastic. A joke right?

https://flowbrackets.com.au/?fbclid=IwAR3jDa4kt6NSlAwq8tcfTr7_p6yQCxNC-ZvYLIqkC3nC5jSI0wMxEJghT7A

I bought this VIC/QLD slimline plate for 14.99. There are other sizes.

https://autobarn.com.au/ab/Autobarn...IM-Victorian-Slimline-Backing-Plate/p/PR00181

 

[Mud]

I bought this VIC/QLD slimline plate for 14.99. There are other sizes.

https://autobarn.com.au/ab/Autobarn-Category/Shop-our-Full-Ranges-by-Brand-|-Autobarn/Kingpin/Kingpin-BK-PL-SLIM-Victorian-Slimline-Backing-Plate/p/PR00181

yeah I used one of those with the cut down OEM bracket
https://www.nissanzclub.com/forum/t...cense-plate-hack-to-fit-slimline-plates.2242/

 

[GUZ]

How did you hide the wires? I'm stuck at the A pillar ?

and where did you put the ground wire?

I hid the wires with the airbag. The ground wire is attached to somewhere near the hood handle.

 

[Supremekai]

I hid the wires with the airbag. The ground wire is attached to somewhere near the hood handle.

I got the a piller off and routed the wires under it.
I don't see the metal part where you have your ground. I'm trying to take the fuse box trim off but don't know how to remove the plastic fastener above the dead pedal... So I can find/use a ground point behind the trim


Edit: finally installed. I used a plier to stick it between 2 of the 4 holes and twist counter clockwise and it came out.

 

[Shobotan]

Pick mine up this Friday

 

[peter]

Fitted front and rear sway bars with new front and rear endlinks from Whiteline yesterday, haven't had a chance to drive yet to see the difference.
Got them through Fulcrum Suspension on a black Friday click and fit offer

 

[MattJ2020]

Pick mine up this Friday

Same color as mine! Love it… but I’ve got the black interior.

On another note, does anyone know how I could remove (in this example) the red interior parts that are red along the dashboard and gearbox area? Want them reupholstered in alcantara ?

 

[Mud]

the red interior parts that are red along the dashboard and gearbox area? Want them reupholstered in alcantara ?

I call these the knee pads, but I think they're referred to as "Console Finishers"
Steps 19 - 30 in this should get them off.

https://www.nissanzclub.com/forum/attachments/mc-10226134-0001-pdf.16297/

I don't think 19 - 24 are required, I don't think you need to remove the console / cup holder assembly. Pretty sure just removing the gear shift surround will be enough to give you access to the screws on the console finishers

 

[nuthed01]

What product did you use or where did you go? And price?

that now makes Rosewood look a bit more burnt brown ??

Makes it look like a dark rum, incredible

 

[Mud]

I bought the Ottocast A2Air and Andriod Auto works great wirelessly, also paired it up with a wireless phone charger that fits in perfectly next to the USB outlets.

Hey @peter
Does this fit in the slot above the USBs? Got a pic of your set up?