Sponsored

Search results

  1. Z1 2025+ Gateway Bypass Harness for ECUTEK Tuning Installation

    fitment is good. I have not driven with it yet. The stock Nissan filter is expensive so I bought the K&N for the high flow. When it’s time to wash it, i will put the stock filter back in for another 10-15K. i noticed that K&N is now making a disposable carbon filter. But not shown for 2023+ Z.
  2. EcuTek Tuning - Nissan has blocked the OBD port on ‘25+

    Finally got this installed along with my HX. Now I’m ready to schedule my ECUTEK tune. https://www.nissanzclub.com/forum/threads/z1-2025-gateway-bypass-harness-for-ecutek-tuning-installation.11129/post-197807
  3. What did you do with your Z today? 🙋🏻‍♂️

    installed my z1 gateway bypass tuning cable https://www.nissanzclub.com/forum/threads/z1-2025-gateway-bypass-harness-for-ecutek-tuning-installation.11129/post-197807
  4. Z1 2025+ Gateway Bypass Harness for ECUTEK Tuning Installation

    Install time is the same as replacing the cabin air filter. Z1 instructions include removing trim panel which is completely unnecessary. Only need to pull the glove box to access and install the harness - same as replacing the cabin air filter. There are 7 screws to remove the glove box and...
  5. What did you do with your Z today? 🙋🏻‍♂️

    Sat overnight and 25F cooler - front = 32 \ rear.= 30
  6. What did you do with your Z today? 🙋🏻‍♂️

    20psi - awesome…. That will get done for sure…
  7. What did you do with your Z today? 🙋🏻‍♂️

    Like Kracker said - traction & handling - looks like Nissan was pushing for an understeer setup with the z. The rear tires have a stiffer sidewall than the fronts - lower air pressure will soften the sidewalls and reduce the spring rate of the tire which will help reduce oversteer.
  8. What did you do with your Z today? 🙋🏻‍♂️

    Thanks for the info. 11.5 a/f was my guess, i assume 19 psi?
  9. What did you do with your Z today? 🙋🏻‍♂️

    re-checked last night (tires sat for only 2hrs) - rear = 32, fronts = 34 with tires. Pic after 35 mile trip. gained = 3psi
  10. What did you do with your Z today? 🙋🏻‍♂️

    Awesome. Did you datalog the dyno pulls with ecutek? Any idea what your a/f & boost numbers are? target vs actual?
  11. What did you do with your Z today? 🙋🏻‍♂️

    They gain 3-4psi during my daily commute. i usually set them close to the factory spec. I think the tires were still warm when i added air last time. This morning the rear was 28-29 cold and fronts were ~33 per the tpms. just checked with a calibrated gage - rears @ 30 and fronts at 34 -...
  12. Tune a must for lower downpipes?

    Untuned and running 3” race lowers mated to a 3” exhaust w\ nismo intake. No power loss but this setup needs a tune for sure. Some gains but not that impressive. No issues with codes..
  13. Best data logger without flashing ECU

    i have the older 3, i would buy the 4 for data logging and use the SD card.. keep in mind these are a dime a dozen. If I was buying a new one - i might would buy one that is compatible with consult iii. Like the vxdiag. https://vxdiag.com/collections/vcx-se-for-nissan
  14. Best data logger without flashing ECU

    https://www.plxdevices.com/Kiwi-OBD-OBDII-Interface-Gauges-Scan-tool-Diagnostics-s/195.htm
  15. What did you do with your Z today? 🙋🏻‍♂️

    Same thing just happened to me. a\c light was off but ac was on. My ‘14 taco will automatically turn the a\c on if the defrost is selected without turning on the a/c light on. So this a programming oversight for nissan and toyota. The a/c light should alway be on if the a/c is on. My ‘07...
  16. Aluminum Oil Pans (Z1 vs. CZP)

    Looks like the Dorman and Z1 will drain better than the CZP. CZP drain is similar to stock except the drain is flush with the floor but raised from the side wall creating pockets on both sides of the drain. i suppose you can have the dorman anodized for less money than the CZP..



Top