• NOTE: THE MEMBERS MARKETPLACE SECTION IS FOR PERSONAL USE ONLY - I.E. SELLING ITEMS/PARTS FROM YOUR PERSONAL VEHICLE ONLY. ANY SALES OF ITEMS MADE FOR COMMERCIAL PURPOSES (I.E. MAKING/SELLING MULTIPLE ITEMS, TAKING ORDERS, ETC) BY ACCOUNTS NOT AUTHORIZED TO CONDUCT COMMERCIAL SALES ON THE SITE IS A DIRECT VIOLATION OF OUR FORUM RULES AND TERMS OF SERVICE AND WILL RESULT IN THE PERMANENT SUSPENSION OF YOUR ACCOUNT.

    ATTENTION SELLERS: All users who wish to sell in the marketplace are now required to abide by the following RULES. If a sales thread/post does not comply, it is subject to DELETION without notice.

    ATTENTION BUYERS: If you see a non-compliant sales thread, please REPORT the thread and take CAUTION when transacting.

    Rule #1 - Post a picture of the actual item you are selling (NO stock photos).
    Rule #2 - The picture must include a REAL piece of paper with your Username and the Date written on it next to the product you are selling. NO photoshop or digitally edited photos are allowed.
    Rule #3 - NO "feeler" threads are permitted. This section is only for items that are actually available and ready to be sold currently.
    Rule #4 - The listing must include an asking price. OBO (or best offer) is allowed but it must be accompanied by an asking price.
    Rule #5 - No "threadcrapping." Classifieds threads are not meant for negative discussions. Comments on pricing are not allowed. Only people with genuine questions and interest in the item for sale should be posting in the classifieds threads.
Sponsored

AMS Intakes Installed, misc. feedback.

staying_tuned

Well-Known Member
First Name
Mike
Joined
Feb 9, 2025
Threads
14
Messages
163
Reaction score
196
Location
Kentucky
Car(s)
23’ Z Performance Manual
Long term I'm planning to go A2A but I got a great deal on these and have always been enamored by AMS hardware across a handful of platforms. I set aside a half-day to do these given most of the feedback out there is that this is challenging. I would imagine this is a nightmare without a few key tools but I happened to have what I needed. The entire process took less than an hour and a half. I'd say half was provisioning and assembly. Unlike everything I've read, the passenger side was twice as fast as my driver's side but as mentioned above, I had what I needed.

I'd recommend making sure you have (at a minimum) the following:

- 12" or better pry tools. Nothign fancy, I've had a $19.99 janky harbor pry tool set for years. I wait and wait for them to fail.
- Baby 1/4" rachet and 1/4" set. Again, any 1/4" set will do. If you don't have a baby ratchet but you have another you can spare, cut it in half with a hacksaw.
- 12" or better slender flathead. Damn ever since craftsman sold out they've been s$it but despite the bend comes in handy, this time is was very handy but a straight 14" or 16" would be ideal, I just didn't have one.

For the passenger side, just use a pry tool on the right clamp but hook it from under. Silly simple. On the left jam your screwdriver between the spring ring and twist to pull it out. It might take a few attempts but not many. Then just yank it out because the screwdriver holds it by itself if positioned right.

That's it. As for the rest in the picture below, I tape and mark everything I touch (getting old and forget a lot). I hit my intake mount grommets (re-used per instructions) with shin-etsu. Last a long time and man it's incredible on all weather seals and other soft rubber & synthetic stripping. I've had this single tube since F&F TD hit. That allen wrench happened to be the exact size for the AMS lid secure bolts. Finally, one of the 300 same sized furniture allen wrenches that I refuse to throw away has been put into use. My tools are never exposed to moisture but those terrible things they include just turn to dust in like 5 years all by themselves somehow hah. I didn't actually use the pliers in the picture but assumed I would and didn't want to take another picture.

Tools. mentioned above:

tools_needed.jpg



Angle on pass clamp using slender screwdriver and hooked pry tool. I'm hooking it from under, I have a closer view that I put a circle around. Doing this you can simply yank the intake out with your other hand because the screwdriver is engaged and twisted, holding the other.


pass_clamp_angles.jpg



Closeup of pry position:
hook_under_clamp.jpg


These plugs were way too stiff to just mash in. I ran them under hot water so they'd soften up, otherwise I'm sure I would have mashed them to death.

plug_clamp.jpg


Finally done and sound great. Going to get some logs out to see if need to iterate on the tune.

ams_intakes_installed.jpg


Ok I hope this helps someone on the fence worried bout getting this done. Get after it!
 

5thZ

Well-Known Member
Joined
Apr 8, 2025
Threads
10
Messages
382
Reaction score
264
Location
Greenville, SC
Car(s)
Nissan Z
Have you sold this yet? I'm not sure if you meant to post here as this is the for sale marketplace section of the forums
 
OP
OP
staying_tuned

staying_tuned

Well-Known Member
First Name
Mike
Joined
Feb 9, 2025
Threads
14
Messages
163
Reaction score
196
Location
Kentucky
Car(s)
23’ Z Performance Manual
Have you sold this yet? I'm not sure if you meant to post here as this is the for sale marketplace section of the forums
Holy moly, thanks for the catch! Old-ness strikes again. @Moderator would it be possible to move this? I tried edit options on both the thread header portion and post content and it doesn’t appear that I can.
 
 






Top