Honestly if you are drilling into the body of your car I'd just buy a new one and get the template with it. You can always use the template and return the spoiler/template when you are done, provided it isn't damaged.
From what I can tell based on my UOA's from blackstone (two so far) the metals are still high after two oil changes. I do have a third sample I need to send off. Now, I'm not an expert at reading the UOA's so how high those numbers are vs the significance of those numbers of the overall oil I...
As far as I know even USDM spec Z's still have the DRL's on during the day even if the headlights themselves are off. Best bet would be to look up the wiring pinouts in the FSM and see. I can't say 100% as I haven't looked at it myself, but I would think that would all be controlled through the...
I already have 3M ceramic on the front and rear window, not much else I could really work with. They are a higher end place, but $6,000 seems pretty up there if they are using the pre cut kits. I could see paying $4,000~ but 6 seems up there. I wasn't expecting it to contribute to the value so...
Had a quote done for PPF - seems a bit excessive, but as I don't know the going rate I feel like I'd rather ask here and get some opinions.
Price quoted was $6,000 ~
This was for a full body ppf with a detail/clean before application and paint correction.
Even still, this seems kinda high...
Without seeing it, hard to say, but I'd bet that its likely the clutch; Ideally you won't need a replacement trans, but either way, if it was due to a defect in labor you should be covered.
Kinda hard to believe a tech doesn't know how to install a clutch, that's a very basic thing. Wouldn't...
A sidenote: Last night I took some time going through the FSM to see if there were any details on diagnosis/troubleshooting the hood pop system, but the only thing I could really come across was a diagnostic procedure in Consult, not any specific "probe with multi meter, if x value keep, if y...
Honestly I'm one of those guys that's big on presentation, so if I had the correct plug I'd probably go through the trouble of soldering the resistor to it, but given the fact that this is intentionally out of sight by design I'd be entirely fine with just inserting the resistor into the harness...
Yeah, that's all this is. I most recently had to do this last year when I swapped my fwd Nissan 200sx with an SR20DET. The SR20DET's don't have an EGR valve, and the USDM SR20DE harness and ECU counterparts did, so that immediately caused a CEL. That is, until I put the resistor into the wiring...
Being that its a basic two pin, it shouldn't be that difficult to find male side that fits. I'm sure if you searched for an exact oem branded replacement you would pay way more than you had to, but any plug of the same dimension would likely work just fine.
If you really didn't care about...
I would only mess with the Nissan Security+ gold if you were going to get one. 3rd party warranties are notoriously bad at wanting to not pay. If you can get the Nissan backed one (regardless of what the dealer tries to shill) you will probably be in better shape if you need to make a claim...
If you would rather pay $150.00 for a resistor that is ten cents, go for it.
There isn't much time, effort, materials, fabrication, or R&D involved here. They are selling you a 10 cent resistor with a plug attached to it at a massive markup. This isn't something that is complex enough in...
Yeah, I've seen that kit a few times. What I'm getting at is its likely a ten cent resistor inside a fancy case that is connected to the male end of the plug to fit into the cars harness. If someone would be willing to take the case off it may likely make it easier and far cheaper for people...
For something as important as the SRS system (which I believe this is tied to given that its yellow), I'm pretty sure its all the same. Otherwise the company selling that kit would have no idea how to make them fit for each individual car.
Question is what resistor would be needed.